Tilton Floor Mount – Aluminum – 2 & 3 pedal (98-1209) Manuel d'utilisateur télécharger pdf

IntroductIon

Please read these instructions before installing the pedal assembly.

Installation instructions for other products from Tilton Engineering are available at

www.tiltonracing.com.

Pedal assembly mountIng

It is very important that the pedal assembly be mounted to a strong and rigid struc-

ture. Flex in the supporting structure reduces control as much as a exible pedal or air

in the lines. The mounting must be strong enough to withstand the loads of a driver’s

legs in a panic situation.

See Diagram 1 for the pedal frame mounting pattern. Putting multiple mounting

holes in two tubes running fore/aft on the car will enable multiple mounting positions,

allowing the entire pedal assembly to be moved for dierent drivers.

A bulkhead is not required to further support the pedal assembly/master cylinders. If

mounting through a rewall, make sure there is enough rewall clearance to allow at

least 1” of pushrod stoke for all master cylinders.

Trial t pedal assembly in place. Be sure to use high quality ne thread fasteners for

the four 5/16” or 8mm mounts on the oor, along with proper full diameter washers.

Proper mounting requires fasteners be used in all four holes.

Note: If using optional throttle linkage kit (P/N 72-791), please install it

to pedal frame prior to mounting pedal assembly to chassis.

balance bar setuP

The 7/16” diameter balance bar (P/N 72-260) included with this pedal assembly has

been set at Tilton to have a 2.50” center-to-center distance for the master clevises.

Please conrm this distance prior to installing master cylinders. Refer to the enclosed

balance bar instruction sheet, P/N 98-1250, for complete balance bar set-up informa-

tion.

remote bIas adjuster routIng

As set at Tilton, the longer thread section of the balance bar is on the right-side of

the brake pedal. This is the end to which the remote bias adjuster cable should be

attached, unless you use a 90 degree coupler (P/N 72-561) to route the cable from the

left-side of the brake pedal. If 90 degree coupler is used of left-side of brake pedal,

remove balance bar and rotate 180 degrees, so that the longer threaded side of the bar

is on the left.

Route the remote bias adjuster cable in a manner that will not interfere with the

throttle pedal throughout the full brake pedal stroke range. This is very important to

prevent an application of the brakes from depressing the throttle pedal. Secure the

cable to the chassis, in a manner that limits the number (and degrees) of bends in the

cable and allows the adjuster to operate smoothly.

Master cylinders sold separately

3.600

2.225

600 Series Forged Aluminum Floor-mount Pedal Assemblies

INSTALLATION INSTRUCTIONS

98-1209

Center

Adjustment

1. Clevis 4. Retaining Ring Clips 7. Pushrod

2. Barrel Nuts 5. Pivot Sleeve 8. Adjusting Shaft

3. Jam-nuts 6. Spherical Bearing 9. Jam-nuts (Pushrod)

90˚ coupler (72-561) installed Bias Adjuster attached

Diagram 1

Balance Bar Diagram

1 2

INSTALLATION INSTRUCTIONS 1

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

IntroductIonPlease read these instructions before installing the pedal assembly. Installation instructions for other products from Tilton Engineering

Page 2

master cylInder mountIngTilton 600-Series Pedal Assemblies are designed to accept Tilton master cylinders.Secure the master cylinders to the pedal fra

Commentaires sur ces manuels

Pas de commentaire

Tilton Floor Mount – Aluminum – 2 & 3 pedal (98-1209) Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Tilton Floor Mount – Aluminum – 2 & 3 pedal (98-1209). Tilton Floor Mount – Aluminum – 2 & 3 pedal (98-1209) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Tilton Floor Mount – Aluminum – 2 & 3 pedal (98-1209)